Animal Feed & Nutrition Division of the Green Agrochem groupTDS · SDS downloadsinfo@greenagrochem.com
Home » PDI Test for Feed Pellets: How Binders Are Evaluated

PDI Test for Feed Pellets: How Binders Are Evaluated

PDI Test for Feed Pellets: How Binders Are Evaluated

The pellet durability index (PDI) is the percentage of pellets, by weight, that stay whole after a standard tumbling test. In the ASAE S269 tumbling-box method, 500 g of cooled, sieved pellets are tumbled in a 30 × 30 × 12 cm box at 50 rpm for 10 minutes, sieved again and weighed: PDI = weight of whole pellets after tumbling ÷ weight before × 100. PDI is the standard way to compare pellet binders such as lignosulfonate.

The Two Common PDI Methods

ItemTumbling box (ASAE S269)Holmen tester
Sample500 g of cooled, sieved pellets100 g of sieved pellets
StressBox with a diagonal baffle, 50 rpm, 10 minPellets blown through a pneumatic circuit
Test timeAbout 10 min plus sievingShort, typically under a minute
ComparabilityWidely used reference in researchGives lower values on weak pellets; not directly interchangeable with tumbling-box results
Modified versionsHex nuts are sometimes added to increase stress for very durable pelletsDifferent run times are used for different feeds
Method summary from Kansas State University Research and Extension (MF3228). Always report which method and settings were used.

How to Run a Fair Binder Comparison

  • Same formula, same mill, same day. Run the control (no binder) and each binder level back-to-back on the same die, conditioning temperature and throughput.
  • Sample after cooling. Take pellets after the cooler, not at the die; hot pellets are softer.
  • Sieve first. Remove fines with the sieve size specified for the pellet diameter before tumbling.
  • Replicate. At least three samples per treatment; report the mean and spread.
  • Record the process. Conditioning temperature, steam, moisture, die L/D ratio, production rate and energy use (kWh/t) all affect PDI as much as the binder.
  • Measure fines in the real chain. PDI predicts fines at feeders; confirm with samples from bulk trucks or feeder lines where possible.

Example Trial Layout for a Lignosulfonate Binder

TreatmentBinder inclusion (complete feed)Notes
Control0Same formula without binder
LowFor example 0.5%Below the EU maximum for all species
MidFor example 0.75%Within the 8,000 mg/kg EU limit for “other” species
HighFor example 1.0%Only for categories with a 10,000 mg/kg EU limit
Inclusion levels are trial examples, not recommendations. Stay within the legal maximum for the species and market.

Feed-grade data sheets follow the EU limits: up to 0.8% of complete feed, or 1.0% for the five categories named in Regulation (EU) 2024/749. Liquid grades are dosed on a solids basis: a 45%-solids liquid at 1.5% of feed supplies about 0.68% dry lignosulfonate product. See calcium lignosulfonate feed grade and liquid lignosulfonate.

Species / category (EU, 1g565)Maximum lignosulphonate, mg/kg complete feed (12% moisture)
Weaned piglets, pigs for fattening, chickens for fattening, laying hens, cattle for fattening10,000 (1.0%)
All other animal species and categories8,000 (0.8%)
Source: Regulation (EU) 2024/749. Composition: Ca, Na or Mg lignosulphonate ≥55%, reducing sugars ≤20% (dry matter).

Interpreting PDI Results

  • A higher PDI means fewer fines, but there is no universal target; set it with the customer and the feeding system.
  • Compare against the control from the same run, not against historical values.
  • If PDI rises but throughput falls or energy use rises, report all three; binder choice is a cost balance.
  • Other factors – fat addition after pelleting, fibre, particle size, starch gelatinisation – can outweigh binder effects.

Frequently Asked Questions

What is a good PDI for feed pellets?

There is no single standard. Targets are set by the feed type and handling chain. Compare treatments against a control from the same production run using the same PDI method.

Is the Holmen PDI the same as the tumbling-box PDI?

No. The two methods apply different stress and give different values, especially for weaker pellets. Report which method was used.

How much lignosulfonate is used in feed pellets?

In the EU the maximum is 8,000 mg/kg (0.8%) of complete feed for most species and 10,000 mg/kg (1.0%) for five named categories; feed-grade data sheets follow these limits. Trials usually test levels below the maximum.

References

Questions about a specification, a test method or a trial: contact us or email info@greenagrochem.com.